Content of the material
- Prep the area
- Tips For Texturing a Wall
- 2. Apply Painter’s Tape
- Texture Drywall
- 5. Test the Mud
- Final Wording
- Skim the walls with the Magic Trowel
- Prepare the joint compound
- Texturing Walls with Paint
- More in Category
- Some COVID-Era Workplace Practices Are Easing, But Others Are Here to Stay
- Measurement Fails in Business, Part II: Real-World Examples and Solutions
- Built to Rent Is Booming, But Operational Challenges Loom for This Housing Sector
- Award-Winning Builder Talks Post-Pandemic Home Design in NAHB Podcast
- Roll on the texture
- AFFILIATES DISCLAIMER
Prep the area
Before starting the project, take a few minutes to prepare your space. Applying texture to a wall is a messy process; lay drop cloths on the floor and use the plastic sheeting and painter’s tape to cover windows, trim, and doorways.
Some walls may require a few simple repairs before adding texture. Patch any holes with the drywall compound, using the drywall knife to press the mixture into the hole. Swipe the area with the edge of the blade to smooth it a bit. Don’t worry about getting the patch perfectly smooth, as it will soon be covered with texture material anyway.
Next, you’ll need to pre-coat the wall. Apply a layer of drywall primer or flat white latex paint, and let it dry. This step is vital. Otherwise, the bare drywall will absorb the texture paint, negating all of your hard work.
Tips For Texturing a Wall
- Don't use a thick-nap roller cover as this picks up too much texturing compound, making it difficult to roll out.
- Work fairly quickly since drywall compound that's spread out dries fast.
- For texturing effects like knock-down, have an assistant follow you with the drywall knife as you roll out the texture.
- For thick wall texture that's drying too slowly, increase heat in the room or turn a fan on low to encourage drying.
2. Apply Painter’s Tape
Lay dropcloths on the floor, adjacent to the baseboards. Mask the crown molding and the baseboards using wide painter’s tape. Place a piece of tape over electrical outlets and light switches.
Protect the floor with a drop cloth and apply wide paper-backed painter’s tape to baseboards, wood trim and to adjacent walls that you will not be texturing.
Prepare the wall by filling cracks, sanding down rough patches and by applying a coat of primer, tinted at the paint store to match your paint color.
Pour twice as much latex paint as you need to paint the entire project into a 5-gallon bucket. Since you’re making a custom paint/texture blend, you must mix the entire batch at one time.
Add drywall powder to the latex paint at the rate of ½-cup of powder for every gallon of paint in the bucket. For example, if you normally use one gallon of paint to simply paint the wall, pour double that amount, or 2 gallons of paint, into the bucket and stir in 1 cup of drywall powder. Stir the thickened paint until it is smooth and free of lumps. This step may take 15 minutes or more.
Pour the paint mixture into a large paint pan and attach a thick-nap roller to an extension pole. Submerge the roller in the paint mixture and begin rolling it on the wall, starting in one corner and working in 3-foot swaths across the wall.
Place the roller at the top of the wall and allow gravity to pull it down without pushing the roller into the wall. Always start at the top and roll down, don’t roll upward and don’t re-roll over the texture.
Refill the roller frequently with the paint mixture for a thick even coat. For a stippled texture, this is all you need to do, but if you want to get creative with your rolled texture, you can add a design.
5. Test the Mud
Insert a roller cover onto a roller handle. Use a low-nap cover to result in a smooth wall texture, or use a thick-nap cover for a more heavily textured look. Dip the roller into the mud mixture. Roll the mud onto a piece of cardboard to test the consistency before you roll it onto the walls. Add more water to thin the mud or more mud to thicken it.
Here you came to know that “how to texture drywall with a roller”. Now you can make your home more beautiful by applying texture to your drywall.
Hope this post “how to texture drywall with a roller” will help you in the right direction. If you have any questions, suggestions or tips then type them in the comment section. We welcome your tips, questions, and suggestions.
Keep Learning Because Life Never Stops Teaching
Skim the walls with the Magic Trowel
After rolling the mud onto your first section, use the magic trowel to smooth it out. The first coat won’t be perfectly smooth. The compound is filling the voids that around the raised surfaces in the existing texture. If you have a really heavy texture, you’ll need more layers of joint compound.
- Each coat of mud should be smoothed in the same direction as it was applied onto the wall with the roller.
- Alternate directions of each consecutive coat.
- If you rolled the mud onto the wall vertically on the first coat, switch to horizontal application for the next coat.
After smoothing out your first section of wall, you’re ready to roll another section with joint compound.
- Keep a wet edge. That’s where the spray bottle full of water comes in handy. Before you start rolling compound onto your second section, lightly mist the edge of the area you just smoothed.
- Slightly overlap the first section as you roll the second section.
The Magic Trowel is like a squeegee. It’s a rubber blade on a handle. It does come with a cover over the blade. Make sure to remove the blade cover!
- Use your damp rag or spray bottle to wet the blade before use.
- Pull the Magic Trowel over the compound, smoothing it out.
- Squeegee the mud in the same direction that you applied it with the paint roller.
If you have really heavily texture patterns, the first coat will not produce perfectly smooth walls. The Magic Trowel may create new lines. Don’t freak out. The next coat will fix that.
Prepare the joint compound
Use a a mixing attachment for your drill to mix the joint compound to the consistency of thick pancake batter. It’s got to be thin enough for you to smooth it on the wall but not so thin that it just drips and dribbles down the wall. You may have to play around with it until you get the “just right” consistency.
If you’re using ready mix mud, add a little water at a time so you don’t end up making it too runny. This is where dry mix can be beneficial. If it does end up too runny, add more dry mix.
Texturing Walls with Paint
Many of the major paint manufacturers offer a line of textured paints. Such products work similarly to drywall mud, but because they are comparatively more difficult to remove, they require greater precision.
For example, when using textured paint, you must work quickly to cover the entire surface before the coat dries. If one area dries before you’ve covered the next, rigid lines may appear at their intersection.
That said, textured paint goes on simply with a standard paint roller and a brush to cut in at edges and corners. Two coats are typically needed, one for the base and another as the finishing layer.
Because textured paints are available in only a limited range of hues, you may wish to pursue a different option—namely, a paint texture additive, which can be mixed with any color of regular paint you like.
More in Category
Some COVID-Era Workplace Practices Are Easing, But Others Are Here to Stay COVID-19 may be easing its grip on the U.S. after a disastrous two years, but lingering supply chain disruptions have builders holding onto their pandemic business tactics Measurement Fails in Business, Part II: Real-World Examples and Solutions If you’re running a home building company and believe numbers equal truth, think again. Numbers do, in fact, lie. Here’s how you can respond to that reality to achieve more reliable business metrics Built to Rent Is Booming, But Operational Challenges Loom for This Housing Sector Don’t let the current hype about single-family B2R communities obscure the need to create long-term sustainability and asset value Award-Winning Builder Talks Post-Pandemic Home Design in NAHB Podcast NAHB’s Housing Developments podcast explores potential solutions for a frenzied post-pandemic business environment
Roll on the texture
Adding texture to a wall must be done in two stages: rolling on the compound and, when that layer is partially dry, applying a second coat. Begin by filling the paint tray with the texture paint or handmade texture compound. Dip your roller into the paint, roll it out, and begin applying it to the wall. A standard roller cover will create a texture, but you may want to try a cover specifically designed for texture. If you’re using store-bought paint, follow all the manufacturer’s directions, as they may only recommend one coat. For corners and other areas that are difficult to reach with your roller, apply the texturing material with the flat face of a paintbrush.
This site maddiary.com contain links to affiliate websites and we receive an affiliate commission for any purchases made by you on the affiliate website using such links. Our affiliates include the following:
- Amazon affiliate programme